Recommended Products
Industrial Battery Monitoring Unit
Monitoring options: battery array up to 2000 AH and 6V to 48V.
BMU Technical Data:
Optional battery type: Acid Lead, Gel, AGM
Battery Voltage: 6V to 48V
Measuring (sampling rate) intervals: can vary from a few minutes to a few days
Device dimensions: 60X120X160 mm
Weight: 350 gr
Operating Temperature: -20°C to +80°C
BMU possible indications:
Battery state of charge.
Battery state of life.
Malfunction of battery charger.
Malfunction of battery connections.
Environmental issues indicators such as temperature and humidity.
DC-DC convertor and regulator 300 A
Specification :
• Electronics DC-DC converter and regulator solves power supply problems for vehicles with high-demanding electrical consumers (up to 300A energy balance).
• The product has dual output of 24V and 12V.
• The product can supply output up to 300A at 24V.
• The product has small form-factor and is very light (0.5 kg)
• The product has a built-in microcontroller and an advanced circuitry to allow maximum efficiency and minimal heating.
Shop
Showing all 17 results
-
Battery management system, Car battery tester
Car battery tester
Comparative Advantages of BMU Device:
- The BMU Device can be connected constantly to high capacity array of batteries (up to 1000 amperes-hour).
- The BMU Device has a low-level of energy consumption.
- The Device is relatively small in size (35 mm.x85 mm.x35 mm.).
- The results can be transmitted through an RS232 telecommunication system.
- The users consider it friendly because of its simplicity.
- The BMU Device has a correction factor, derived from the environment temperature.
- The BMU Device allows wide variability of the test frequency.
SKU: BMU01 -
DC-DC convertor and regulator
DC-DC convertor and regulator 300 A
Specification :
• Electronics DC-DC converter and regulator solves power supply problems for vehicles with high-demanding electrical consumers (up to 300A energy balance).
• The product has dual output of 24V and 12V.
• The product can supply output up to 300A at 24V.
• The product has small form-factor and is very light (0.5 kg)
• The product has a built-in microcontroller and an advanced circuitry to allow maximum efficiency and minimal heating.SKU: 654613612 -
PWM Fan speed control driver
Glow Plugs smart controller
Product Description:
Product is a customized unit for each model of diesel vehicle.
Products has built-in microcontroller and advanced circuitry to allow full control of glow-plugs pre-heating cycle and functionality, which leads to much longer plug’s life.
Product provides control panel indication (pre-heating sign is blinking when faulty plug detected, more problems – more frequent blinking).Read More about Glow-Plugs Life Enhancer
SKU: n/a -
Battery management system, Industrial Battery Monitoring Unit
Industrial Battery Monitoring Unit
Monitoring options: battery array up to 2000 AH and 6V to 48V.
BMU Technical Data:
Optional battery type: Acid Lead, Gel, AGM
Battery Voltage: 6V to 48V
Measuring (sampling rate) intervals: can vary from a few minutes to a few days
Device dimensions: 60X120X160 mm
Weight: 350 gr
Operating Temperature: -20°C to +80°CBMU possible indications:
Battery state of charge.
Battery state of life.
Malfunction of battery charger.
Malfunction of battery connections.
Environmental issues indicators such as temperature and humidity.SKU: BMU02 -
Smart Led Load Resistor, Smart Led Load Resistor 2 way 21W 12V for replaces 2 standard LED Load resistors
LED LOAD RESISTOR FOR VEHICLE TURN SIGNALS 2-way X 21W , 12 volt
Smart Led Load Resistor, Smart Led Load Resistor 2 way 21W 12V for replaces 2 standard LED Load resistorsLED LOAD RESISTOR FOR VEHICLE TURN SIGNALS 2-way X 21W , 12 volt
Smart LED load resistor for vehicle turn signals 21w 12 volt – replacement of standard LED load resistor
The not heated Smart load module for LED (replacing standard LED load resistor) – read more
PRODUCT SPECIFICATION:
- Fixes error messages caused by the on-board computer after replacing incandescent light bulbs with LEDs
- The computer will properly detect LED functionality
- Smart module is not heated(Unlike existing load devices) and does not require additional cooling equipment
- There is a two-channel(two-way) module for replacing the right and left turn signal of a car and a 4-channel module (for buses and trucks)
- Reduces the likelihood of vehicle battery discharge when lights are left on(Unlike existing load devices)
When you using Gambeks smart load resistor for led turn signals module instead of a LED load resistor, the 12v module SLM22112 replaces 2 LED Load resistors with a capacity of 21 watts each. The Gambeks SLM22112 smart load resistor module is a modern, non-heating solution for automotive turn signal upgrades, offering easy installation and reliable operation.
SKU: SLM22112 -
LVD - Low Voltage Disconnect
Low Voltage Disconnect (LVD) 12v – 1A
This battery guard will automatically disconnect any load and appliances connected through it when the battery voltage goes below a low voltage threshold, and it will also disconnect the appliances if the voltage is too high or the current exceeds 1A
Low Voltage Disconnect (LVD) Features:
- Disconnects battery at pre-set voltage
- Stops battery damage due to excessive discharging
- Reconnects battery once power is restored
- Measurement accuracy: ± 0.05 volts
- Calibrate and change disconnection and connection voltages with the laboratory voltage supplier.
- Compact, lightweight and easy to install
- Protection against polarity reversal
SKU: EL0112 -
Low Voltage Disconnect (LVD) - 12v, LVD - Low Voltage Disconnect
Low Voltage Disconnect (LVD) 12v – 10A
Low Voltage Disconnect (LVD) - 12v, LVD - Low Voltage DisconnectLow Voltage Disconnect (LVD) 12v – 10A
This battery guard will automatically disconnect any load and appliances connected through it when the battery voltage goes below a low voltage threshold, and it will also disconnect the appliances if the voltage is too high or the current exceeds 10A
Low Voltage Disconnect (LVD) Features:
- Disconnects battery at pre-set voltage
- Stops battery damage due to excessive discharging
- Reconnects battery once power is restored
- Measurement accuracy: ± 0.05 volts
- Calibrate and change disconnection and connection voltages with the laboratory voltage supplier.
- Compact, lightweight and easy to install
- Protection against polarity reversal
SKU: EL1012 -
Low Voltage Disconnect (LVD) - 24 v
Low Voltage Disconnect (LVD) 24v – 10A
The Low Voltage Disconnect (LVD) module EL1024 monitor the battery voltage and automatically disconnects non critical loads when LVD senses that vehicle battery voltage is low or automatically reconnects when voltage is restored. The Low Voltage Disconnect device, that can be used to protect batteries from damage and help extend battery life.
Low Voltage Disconnect (LVD) Features:
- Disconnects battery at pre-set voltage
- Stops battery damage due to excessive discharging
- Reconnects battery once power is restored
- Measurement accuracy: ± 0.05 volts
- Calibrate and change disconnection and connection voltages with the laboratory voltage supplier.
- Compact, lightweight and easy to install
- Protection against polarity reversal
SKU: EL1024 -
Low Voltage Disconnect (LVD) - 24 v
Low Voltage Disconnect (LVD) 24v – 1A
The Low Voltage Disconnect (LVD) module EL0124 monitor the battery voltage and automatically disconnects non critical loads when LVD senses that vehicle battery voltage is low or automatically reconnects when voltage is restored. The Low Voltage Disconnect device, that can be used to protect batteries from damage and help extend battery life.
Low Voltage Disconnect (LVD) Features:
- Disconnects battery at pre-set voltage
- Stops battery damage due to excessive discharging
- Reconnects battery once power is restored
- Measurement accuracy: ± 0.05 volts
- Calibrate and change disconnection and connection voltages with the laboratory voltage supplier.
- Compact, lightweight and easy to install
- Protection against polarity reversal
SKU: EL0124 -
Smart Led Load Resistor, Smart Led Load Resistor 2 way 21W 24V for replaces 2 standard LED Load resistors
SMART LOADs FOR AUTOMOTIVE LED (REPLACEMENT FOR LED LOAD RESISTOR) 2-way X 21W , 24 volt
Smart Led Load Resistor, Smart Led Load Resistor 2 way 21W 24V for replaces 2 standard LED Load resistorsSMART LOADs FOR AUTOMOTIVE LED (REPLACEMENT FOR LED LOAD RESISTOR) 2-way X 21W , 24 volt
Electronic smart module for load simulation and fix failure control of LED Turn Signal Error
The not heated Smart load module for LED (replacing standard LED load resistor)– read more
PRODUCT SPECIFICATION:
- Fixes error messages caused by the on-board computer after replacing incandescent light bulbs with LEDs
- The computer will properly detect LED functionality
- Smart module is not heated(Unlike existing load devices) and does not require additional cooling equipment
- There is a two-channel(two-way) module for replacing the right and left turn signal of a car and a 4-channel module (for buses and trucks)
- Reduces the likelihood of vehicle battery discharge when lights are left on(Unlike existing load devices)
The 24 v module SLM22124 replaces 2 LED Load resistors with a capacity of 21 watts each.
The module does not heat up and therefore does not require installation on a radiator.
SLM smart LED load module Installation Instructions
SKU: SLM22124 -
Smart Led Load Resistor, Smart Led Load Resistor 4 way 21W 24V for replaces 4 standard LED Load resistors
SMART LOADs FOR AUTOMOTIVE LED 4-way X 21W , 24 volt
Smart Led Load Resistor, Smart Led Load Resistor 4 way 21W 24V for replaces 4 standard LED Load resistorsSMART LOADs FOR AUTOMOTIVE LED 4-way X 21W , 24 volt
Electronic smart module for load simulation and fix failure control of LED Turn Signal Error
The not heated Smart load module for LED (replacing standard LED load resistor) – read more
PRODUCT SPECIFICATION:
- Fixes error messages caused by the on-board computer after replacing incandescent light bulbs with LEDs
- The computer will properly detect LED functionality
- Smart module is not heated(Unlike existing load devices) and does not require additional cooling equipment
- There is a two-channel(two-way) module for replacing the right and left turn signal of a car and a 4-channel module (for buses and trucks)
- Reduces the likelihood of vehicle battery discharge when lights are left on(Unlike existing load devices)
The module SLM42124 – 24 v replaces 4 LED LOAD resistors with a capacity of 21 watts each.
The Gambeks SLM42124 smart load resistor module is an advanced, non-heating solution designed for automotive turn signal LED upgrades.SLM smart LED load module Installation Instructions
SKU: SLM42124 -
Smart Led Load Resistor, Smart Led Load Resistor 4 way 21W 12V for replaces 4 standard LED Load resistors
SMART LOADs FOR FIX AUTOMOTIVE LED TURN SIGNAL ERROR – 4-way X 21W , 12 volt
Smart Led Load Resistor, Smart Led Load Resistor 4 way 21W 12V for replaces 4 standard LED Load resistorsSMART LOADs FOR FIX AUTOMOTIVE LED TURN SIGNAL ERROR – 4-way X 21W , 12 volt
Electronic smart module for load simulation and fix failure control of LED Turn Signal Error
The not heated Smart load module for LED (replacing standard LED load resistor)– read more
PRODUCT SPECIFICATION:
- Fixes error messages caused by the on-board computer after replacing incandescent light bulbs with LEDs
- The computer will properly detect LED functionality
- Smart module is not heated(Unlike existing load devices) and does not require additional cooling equipment
- There is a two-channel(two-way) module for replacing the right and left turn signal of a car and a 4-channel module (for buses and trucks)
- Reduces the likelihood of vehicle battery discharge when lights are left on(Unlike existing load devices)
When you using Gambeks smart load resistor for led turn signals module instead of a LED load resistor, the module 12 v SLM42112 replaces 4 LED LOAD resistors with a capacity of 21 watts each.
The Gambeks SLM42112 provides reliable operation, simple installation, and enhanced safety by eliminating the heat and failure detection issues common with traditional LED load resistorsSLM smart LED load module Installation Instructions
SKU: SLM42112 -
Industrial Battery Monitoring Unit
Telecom Battery Monitoring Unit
BMU Technical Data:
Optional battery type: Acid Lead, Gel, AGM
Battery Voltage: 6V to 48V
Measuring (sampling rate) intervals: can vary from a few minutes to a few days
Device dimensions: 60X120X160 mm
Weight: 350 g
Operating Temperature: -20cel to +80celSKU: bmu03 -
Automotive DC-DC voltage converter, DC-DC convertor and regulator
Unique Solutions UPS DC-DC 12v for all types of vehicles
Automotive DC-DC voltage converter, DC-DC convertor and regulatorUnique Solutions UPS DC-DC 12v for all types of vehicles
A 12V DC-DC UPS provides uninterruptible 12V power to vehicle-mounted equipment and is available for a wide range of vehicle applications including trucks, buses, boats, emergency vehicles, airplanes, and even military systems.
The UPS products has network connection protocol (optional ).The UPS products has built-in logic and brand-new circuitry for maximum reliability control and life time. The UPS products comply MIL-STD-810 and MIL-STD-1275 standards.
SKU: PT0005 -
DC-DC UPS, DC-DC UPS 24 v
Unique Solutions UPS DC-DC 24v for all types of vehicles
A 24V DC-DC UPS provides uninterruptible 24V power to vehicle-mounted equipment and is available for a wide range of vehicle applications including trucks, buses, boats, emergency vehicles, airplanes, and even military systems.
The UPS products has network connection protocol (optional ).The UPS products has built-in logic and brand-new circuitry for maximum reliability control and life time. The UPS products comply MIL-STD-810 and MIL-STD-1275 standards.
SKU: UPS00024 -
PWM Fan speed control driver
Universal Fan speed control driver
The Universal PWM Fan speed control driver for the fan speed control in automotive 24 volt climate control systems
The Universal PWM DC Fan Speed Control Driver emerges as a vital component in managing the fan speed within 24-volt climate control systems, providing precise control and adaptability for various driving conditions.
Fan speed control Function:
- High efficiency speed controller for DC Fan Motor
- Suitable for 24 volt systems
- Protection: Electronic Short circuit Protection, No fuse needed
- PWM speed control
- Maximum Load: 400W
- DC input voltage range 18V – 32V
- Use different kinds of input control: Potentiometer , Encoder and Push button
Read More
SKU: n/a
